Specifications

• Power Rating:
• from 0.13 HP to 0.75 HP
• Shaft Length:
• PP and PVDF from 600 to 1400
• AISI 316 from 850 to 2000
• Motor:
• direct or gear
• 220, 380 or 12 V
• from 35 to 940 rpm.
• Weight:
• from 5 to 14.5 kg

These portable drum pumps, particularly suitable for pumping corrosive fluids, work immersed in fluid.

Their form of construction has been specifically designed to collect any spills in the barrel of fluid.

Available with electric motor or pneumatic motor interchangeable, these pumps have open rotor allows continuous flow pumping of clean corrosive fluids with viscosity up to 600cps apparent engine and tire 500 watts (at 20°C) and up to 900cps powered at 800 watts (at 20°C). Versions powered by electric motor, TR-EL series are also equipped with safety switch to prevent accidental restart the pump after a power cut.

Main advantages

• Run in PP, PVDF and Aisi 316
• Economic
• Portable
• Suitable for corrosive fluids
• Viscosity up to 900 cps
• Available with electric motor and tire
• Adjust flow (pneumatic version)
• Lack of required mechanically operated invalid chairs
• Easily removable Float length = 900 mm or 1200 mm
• Range up to 90 l / min

The flow meter, flow meters, flow meters or volumetric wheel oval AM series to obtain measurements accurate, high repeatability, even very viscous liquid, up to 1,000,000 cps.

Ease of use, compactness, possibility of independent power supply by batteries make these products suitable for installation on fixed lines and fluid transfer and distribution, both for mobile applications such as valves and accessories guns distribution for any other industrial application control fluid provided.

Applications

In the food industry for:
Pulp & juice, glucose, glucose syrup, melted butter, Yogurt, cooking oil, sauces, Mayonnaise, Alcoholic beverages, Mustard, Wine, Must, Milk, Olive oil, seed oil, tomato sauce, beer, etc..

In the chemical industry for:
Colle, Glycerine, emulsifying wax, detergent, photographic processing fluids, industrial inks, polyelectrolytes, Ammonia, Caustic Soda-acetone-Butane, soap, oil, acids, solvents, paints business, car paint, heavy oils, Kerosene, Oil , oil, Freon, Grease, Paints, Stucco

Cosmetics and pharmaceutical industry for:
Creams, shampoo, liquid soap, cleansing milk, Balsamo, Mouthwash, Alcohol, toothpaste, gels, perfumes, syrups, glycerine, glucose solution, Water, Vaseline

Marine industry for:
Heavy oils, Kerosene, Oil

Features

• Range up to 1200 lpm
• Liquid temperature up to 120°C
• Pressure up to 55 BAR
• Suitable for low viscous liquids and high viscosity (up to 1,000,000 cps)
• High accuracy: + / -0.5%
• Repeatability: 0.03%
• High frictional resistance
• Few worn components
• Flowmeter standard Hall Effect or Reed Switch
• All M-Series flow meters are ISO / IEC 17025:1999
• All M-Series flow meters are CE
• All M-series flow meters have specific ratio calibration
• Next-generation digital display that can be installed on both the flow meter or remotely, with:
  • Ability to preset the amount controlled by a phase
  • Ability to preset the amount controlled two-step or pulse output
  • Possible analog output 4-20 mA
  • Can be connected to a computer with 4 wires or cables RS232/RS485-2 / TTL & Communication Protocol Modbus ASCII / RTU
  • Selection screen units: ml, L, m3, GAL, U.S. GAL, kg, lb, bbl
  • Screen with light for night operation
  • Figures of 17 millimeters
• ATEX: II 1 GD EEx ia IIB / IIC T4 T 100°C
• EC - Certificate KEMA 03 ATEX 1074 X

The operation of the peristaltic pump is obtained via a "sliding pressure" acting on a hose, this pressure is exerted by the sliding rollers that rotate parallel to an axis, supported by a roller-door. The slow rotational movement of the holder support rollers is transmitted by two or three steps geared to 35, 86 or 141 rpm. Equipped with an electric motor MEC-56 from 0,09 kW (1 / 8 CV) regime of 1450 rpm. continuous service.

The inside of the pump body and the door-turned-rollers are tolerant of precision, individually calibrated during assembly and subsequent testing to distribute uniform pressure on the tube-membrane, thus ensuring a perfect self-priming and a longer life the tube-membrane.

Absence of valves and closures.
NORTON tubes are extruded with high precision in order to prevent occlusion and a reduced volumetric rendering. Easy cleaning and maintenance.
Very robust, pump body in cast aluminum, painted with epoxy resin.
Portarulli anodized aluminum, axles and oversized bearings.
Max. Intake approximately 8 m. tube up to Ø 12.7 mm. and about 6 m. tube Ø 15,9 mm.
Max. allowed for the tube: 1.4 Kg/cm².
Max. 60ºC.
These pumps are capable of pumping viscous liquids and particles in suspension, without suffering any damage.
Retain the liquid in its passage, prevent backflow of the liquid and the effect "siphon".
Ability to work on dry and reverse the direction of rotation.
The regime of 35 rpm. is suitable for high viscosity liquids (polyelectrolytes) or which do not undergo any changes you want (high quality wines).

In this section we present a wide range of accessories progettatti order to implement the performance of our pumps and facilitate their use by the operator.

Accessories for transfer at a predetermined cycle (click here to see the animation), Sensors Contacolpi, flanges and valves, etc..

Also presented special pump to always provide the best product for your needs: stainless steel or cast iron centrifugal pumps, electric pumps, submersible pumps, and more.